This wallpaper calculator uses the proper decorator method rather than a rough area guess. It works out the length of each drop, rounds that length up to a whole pattern repeat when your paper has one, and then counts how many drops fit across your walls and how many drops each roll gives you.
Estimates only. Doors are counted at 0.9 m wide and windows at 1.2 m wide, and the drops saved over a window can usually be pieced from offcuts above and below it, so the roll count errs on the safe side.
How to use it
- Measure the room, either as a length and width or as up to four separate wall widths if the room is an odd shape.
- Add the wall height, floor to ceiling, and count the doors and windows so their widths come off the total.
- Pick your roll size. The presets cover the UK standard roll, the UK wide roll and the US double roll, or type a custom size.
- Enter the pattern repeat printed on the roll label, or leave it at 0 for plain paper.
- Read off the drops needed, the drops each roll gives, and the rolls to buy, with a spare roll figure alongside.
How the calculation works
Each drop is the wall height plus a 10 cm trimming allowance, and if the paper has a pattern repeat, the drop length is rounded up to the next whole repeat so the pattern lines up across drops. Dividing the roll length by the drop length gives the drops per roll. Each wall width is divided by the roll width and rounded up, because a part width still needs a full drop, and the door and window widths are then taken off. Finally the total drops are divided by the drops per roll and rounded up to whole rolls.
Worked example. A room 4 m by 3.5 m with a 2.5 m ceiling needs 8 drops on each long wall and 7 on each short wall at a 53 cm roll width, 30 drops in all. One door and one window save 3 drops, leaving 27. Each drop is 2.5 m plus 10 cm, rounded up to the 32 cm repeat, so 2.88 m, and a 10.05 m roll gives 3 drops. That works out at 9 rolls, or 10 with a spare kept back.
Standard roll sizes
| Roll | Size | Covers about |
|---|---|---|
| UK standard | 53 cm x 10.05 m | 5.3 m² |
| UK wide | 70 cm x 10.05 m | 7.0 m² |
| US single | 20.5 in x 16.5 ft | 28 sq ft |
| US double | 20.5 in x 33 ft | 56 sq ft |
Coverage on the label is the flat area of the roll, not the wall area you will finish with. Pattern repeat, trimming and part drops at corners all eat into it, which is why the drop method in this tool gives a safer count than dividing wall area by roll area.
Mistakes to avoid
- Dividing the wall area by the roll area. That ignores drop lengths and pattern matching and almost always undercounts the rolls.
- Ignoring the pattern repeat. A large repeat can add a whole extra drop of waste per roll, so check the label before ordering.
- Buying rolls from different batches. Shade can vary slightly between batches, so order everything in one go and note the batch number.
- Forgetting the ceiling slope or a chimney breast. Measure the longest drop on a sloping ceiling and add chimney breast walls as separate widths.
- Ordering paste by guesswork. One standard tub or packet covers roughly 4 to 5 rolls, and running out mid wall is a miserable delay.
Painting some walls instead? The paint calculator works out litres and tin sizes, the curtain size calculator sizes the window dressing for the same room, and the room size calculator gives you the floor and wall areas to plan around.
Common questions
How many rolls of wallpaper do I need for a standard room?
A typical double bedroom with a standard UK roll and a modest pattern repeat usually lands around 8 to 10 rolls. The exact figure depends on the drops per roll, which is why entering your own measurements and repeat above beats any general rule.
Why does the pattern repeat change the roll count?
Each drop has to start at the right point in the pattern so motifs line up across the wall. That means cutting each drop to a whole number of repeats, and the offcut between the ceiling line and the next repeat is waste, so fewer drops fit on each roll.
Should I buy a spare roll?
Yes, if the budget allows. One unopened roll from the same batch covers a damaged drop, a stain repair or a future patch, and matching the batch months later is often impossible. Most shops accept returns of unopened rolls if you end up not needing it.
How much paste do I need?
One standard tub of ready mixed paste, or one packet of flake paste mixed up, covers about 4 to 5 rolls. Heavy or washable papers can use more, so check the paste guidance on the roll label for anything unusual.
Do I take doors and windows off the count?
Yes, this tool takes standard widths off for each door and window. The saving is cautious, because the short lengths above a door and above and below a window can often be pieced from offcuts rather than cut as new drops.
