Radiator BTU Calculator

This radiator BTU calculator estimates how much heat a room loses, then tells you the radiator output you need to replace it. It gives the answer in watts and BTU, and it corrects the size for modern low temperature systems and heat pumps, where radiators need to be bigger than the old boiler figures suggest.







Estimates only. This is the standard simplified sizing method used for a first guide. A heating engineer will also weigh up window sizes, floor type and pipe runs before fixing the final radiator sizes.

How to use it

  1. Measure the room: length, width and ceiling height, in metres or feet.
  2. Pick the room type, because a bathroom is kept warmer than a hallway and needs more heat per cubic metre.
  3. Set the glazing, the number of external walls and the insulation level. These adjust the answer up or down.
  4. Pick your heating system. A standard boiler runs hot, while a heat pump runs much cooler and needs larger radiators for the same room.
  5. Read off the heat the room needs and the catalogue rating to buy, then split it across two radiators if the figure is large.

How the calculation works

The tool uses the simplified method most plumbers start with. It multiplies the room volume in cubic metres by a watts per cubic metre factor for the room type, then adjusts the result: single glazing adds about 15 percent, triple glazing takes off about 10 percent, each external wall adds about 5 percent, poor insulation adds 20 percent and good insulation takes off 15 percent. Watts convert to BTU at 3.412 BTU per watt. Radiator catalogue ratings are quoted at Delta T50, which means the water is much hotter than the room. At Delta T30 a radiator only gives out about 51.5 percent of its catalogue output, and at Delta T20 only about 30.4 percent, so the tool divides by that factor to give the bigger rating you actually need to buy.

Worked example. A living room of 4 m by 3.5 m with a 2.4 m ceiling has a volume of 33.6 cubic metres. At 50 watts per cubic metre that is 1,680 watts, and two external walls add 5 percent, giving 1,764 watts, or about 6,019 BTU. On a standard boiler that is the rating to buy; on a heat pump at Delta T20 you would need a radiator rated around 19,800 BTU at Delta T50, which is why heat pump systems use much larger radiators.

Room temperatures and heat factors

Room Target temp Watts per m³
Living room 21 °C 50
Bedroom 18 °C 45
Bathroom 22 °C 65
Hallway 16 °C 40
Kitchen 18 °C 45

Bathrooms carry the highest factor because they are kept warmest and often have tiled floors and an outside wall. Bedrooms and kitchens sit lower because most people sleep and cook comfortably in cooler air.

Mistakes to avoid

  • Buying on the catalogue figure with a heat pump. At low flow temperatures the same radiator gives out a fraction of its Delta T50 output, so always correct the rating first.
  • Ignoring the external walls. A corner room with two or three outside walls loses far more heat than the same room in the middle of the house.
  • Sizing from floor area alone. A tall ceiling means more air to heat, so volume matters, not just square metres.
  • Undersizing a bathroom. Towel rails look the part but many give out far less heat than a proper radiator, so check the BTU figure before relying on one.
  • Forgetting the boiler or heat pump limit. Oversized radiators are fine, but the heat source still has to cover the whole house total.

Planning the room around the radiator? The bathroom cost calculator prices a full refit including heating, and the room size calculator works out your floor and wall areas for the rest of the project.

Common questions

What does Delta T mean for a radiator?

Delta T is the gap between the average water temperature inside the radiator and the room temperature. Catalogue ratings use Delta T50, but a condensing boiler often runs nearer Delta T30 and a heat pump nearer Delta T20, and output falls steeply as the gap shrinks.

Why do heat pumps need bigger radiators?

A heat pump heats water to a lower temperature than a boiler, so each radiator gives out less heat. At Delta T20 a radiator produces roughly 30 percent of its Delta T50 rating, so the radiator has to be much larger, or the room will never reach temperature.

Is one big radiator better than two smaller ones?

Two smaller radiators usually give a more even heat, especially in long or L shaped rooms, because the warmth comes from two points instead of one. One large radiator is simpler to pipe and can be cheaper to buy, so it comes down to the room shape.

How accurate is this calculator?

It is a sensible first guide based on room volume and standard adjustment factors, and it lands close to most professional quick sizings. It cannot see your exact window areas, floor build up or exposure to wind, so treat it as the starting point for a conversation with a heating engineer.

What BTU radiator do I need for a bedroom?

A typical double bedroom of about 12 square metres with average insulation needs roughly 4,000 to 5,500 BTU on a standard boiler system. Enter your own measurements above for a figure based on your room rather than a general range.