Your fence shopping list
Estimates only. Post mix is worked out at two 20 kg bags per post for a standard hole about 60 cm (2 ft) deep. Check your fence line for steps in ground level before ordering, and treat any cut panel edges with preservative.
This fence panel calculator works out how many panels, posts, bags of post mix and gravel boards you need for up to three runs of garden fencing. It rounds each run up to whole panels, which is how fences are actually bought and built, so the shopping list matches what you will really buy.
How to use it
- Measure each straight run of fence in metres or feet. A run ends at a corner, a step in the ground or a gate.
- Enter the runs, then check the panel width. The standard width is 1.83 m (6 ft), and most UK panels are sold at that size.
- Pick your panel height and post type, and tick gravel boards if you plan to fit them under the panels.
- If your runs join at corners, tick the corner box so that shared corner posts are only counted once.
- Add prices if you want a rough materials cost, then read your shopping list in the results panel.
How the calculation works
Panels are counted run by run. Each run length is divided by the panel width and rounded up, because a panel cannot bend round a corner or stretch across two runs. The final panel in a run is normally cut down to close the remaining gap.
Posts are counted as panels plus one for each run, because every run needs a post at both ends. Where two runs meet at a corner, they share the corner post, so the corner option takes one post off for each join. Post mix is estimated at two bags per post, and gravel boards are counted at one per panel when that option is on.
Worked example: a 10 m back fence with a 6 m side fence joining it at a corner needs 6 panels for the first run and 4 for the second, so 10 panels in total. The posts come to 12 before the shared corner is taken off, leaving 11 posts, 22 bags of post mix and 10 gravel boards.
Mistakes to avoid
- Measuring the whole garden outline as one long run. Corners need their own post, so always measure and count run by run.
- Ordering posts as total panels plus one. Each separate run needs its own end post, so side fences add more posts than people expect.
- Forgetting the cut panel. The last panel in a run is usually trimmed to fit, so measure the final gap once the posts are set rather than trusting the plan.
- Setting posts too shallow. About 60 cm (2 ft) of the post should sit in the ground, so a 6 ft panel needs an 8 ft post.
- Skipping gravel boards on ground that stays wet. The board takes the rot and the strimmer damage instead of the panel itself.
Panel heights and post lengths
| Panel height | Typical use | Post length to buy |
|---|---|---|
| 3 ft (0.9 m) | Low front garden fence | 5 ft (1.5 m) |
| 4 ft (1.2 m) | Front gardens, low boundaries | 6 ft (1.8 m) |
| 5 ft (1.5 m) | Side boundaries, some privacy | 7 ft (2.1 m) |
| 6 ft (1.83 m) | Full privacy, back gardens | 8 ft (2.4 m) |
Planning a bigger garden project? Work out your boards with the decking calculator, and check any new rooms or extensions with the room size calculator.
Frequently asked questions
How many fence panels do I need for a 10 metre fence?
With standard 1.83 m panels, a 10 m run needs 6 panels. The six panels cover 10.98 m, so the final panel is cut down to close the gap neatly.
How many posts do I need for my fence?
Allow one more post than the number of panels in each run, so a 6 panel run needs 7 posts. If runs join at a corner, the corner post is shared and you can order one fewer for each join.
How many bags of post mix does one post need?
Most post holes take about two 20 kg bags of post mix for a hole roughly 60 cm deep. Very soft ground or a deeper hole can take a third bag, so many people order one spare bag for every few posts.
Can I cut a fence panel to fit?
Yes. Lap and closeboard panels can be trimmed to width with a saw, then treated on the cut edge with preservative. Measure the final gap once the posts are set, because post positions rarely land exactly where the plan put them.
Do I really need gravel boards?
They are not compulsory, but they lift the panel clear of wet soil and take the rot and strimmer damage instead of the panel. On most fences they pay for themselves by making the panels last longer.
