Backsplash Calculator

This backsplash calculator works out how many tiles or mosaic sheets your splash zone needs. In the UK the same job is called a splashback, and the maths is identical: add your counter runs, splash height and tile size to get the area, the tile count with layout waste, the boxes to buy and a grout estimate.




Estimates only. The socket deduction is a flat allowance of about 100 square centimetres, roughly 16 square inches, per socket, and tiles are normally cut around sockets rather than removed. Check your tile batch and box coverage before ordering.

How to use it

  1. Measure each run of counter that needs tiling, along the wall, and add the runs in the first three boxes.
  2. Add the splash height, from the worktop up to where the tiles will stop, often the underside of the wall units.
  3. Take off anything that will not be tiled: the window over the sink and the sockets on the wall. The tool uses a small flat deduction per socket.
  4. Pick your tile type, or type a custom size, and set the layout, because diagonal and herringbone patterns waste more tiles.
  5. Read off the net area, the tile or sheet count, the boxes to buy and the grout estimate.

How the calculation works

The area is the total run length multiplied by the splash height, minus the window area and the socket allowance. The tile count is that net area divided by the area of one tile or sheet, with the layout waste added on top, then rounded up to whole tiles and whole boxes. The grout figure is a simple area based estimate that rises for small tiles and mosaic.

Worked example. Two runs of 250 cm and 150 cm at 50 cm high give a gross area of 2.00 square metres. A window of 100 by 50 cm takes off 0.50 square metres and five sockets take off 0.05, leaving 1.45 square metres to tile. A subway tile of 10 by 20 cm covers 0.02 square metres, so the area needs 72.5 tiles of coverage, and 80 whole tiles once 10 percent waste for a straight layout is added. That is 2 boxes of 50, with about 0.7 kg of grout.

Standard splash heights

Splash height Where it suits Worth knowing
10 cm (4 in) Upstand only Matches a worktop upstand, quick to fit
45 cm (18 in) Most kitchens The standard gap under wall units
60 cm (24 in) Tall splash zones Suits high wall units and large pans
Full height Hob and cooker wall Tile up to the extractor or the ceiling

Standard heights cover most kitchens, but the hob wall is the one place worth going full height. Steam, splashes and heat reach well above 45 cm behind a cooker, and a full height splash there is easier to wipe down.

Mistakes to avoid

  • Measuring the worktop instead of the wall. Measure along the wall, corner to corner, counting corners once.
  • Forgetting the return walls. A short return at the end of a run is easy to miss and leaves you a few tiles short.
  • Ordering the exact count. Cuts, breakages and one cracked tile in the box are normal, which is what the waste allowance is for.
  • Mixing batches. Buy all boxes in one go so the colour batch matches.
  • Skipping the socket plan. Sockets are cut around, not tiled over, so mark where they sit first.

Doing the floor or a full wall as well? Use the tile calculator for the bigger area, the grout calculator for a closer grout figure, and the kitchen cost calculator to price the whole job.

Common questions

How high should a kitchen backsplash be?

For most kitchens the splash fills the gap between the worktop and the wall units, which is usually 45 to 60 cm, or 18 to 24 inches. Behind a hob, take the tiles full height to the extractor if you can.

Are backsplash and splashback the same thing?

Yes. Backsplash is the word used in the US and splashback is the word used in the UK, and both mean the tiled area behind a worktop. The measuring and the tile maths are identical either way.

How much waste should I add for cuts?

Add 10 percent for a straight or brick layout, 15 percent for diagonal, and 20 percent for herringbone, because angled patterns cut far more part tiles. The tool adds the figure for the layout you pick.

Do sockets change the tile count?

Only slightly. Tiles are cut around sockets rather than left out, so this tool takes off a small flat allowance of about 100 square centimetres per socket to cover the trimming.

How much grout will I need?

The estimate here is based on the tiled area and the tile size. Small tiles and mosaic sheets have far more joints, so they use much more grout per square metre than large tiles. Check the coverage printed on the grout bag for your joint width.