Please check your numbers. Tile size, joint depth and area all need to be above zero.
Your grout estimate
Estimates only. Densities used: sanded cement grout 1.6 kg per litre, unsanded 1.5 kg per litre, epoxy 1.7 kg per litre. Real usage varies a little with trowel technique and how much is washed off the tile faces, so the calculator rounds bags up.
Buying grout on its own, or checking the tile calculator figure in more detail? Enter your tile size, joint width, joint depth and area, and this grout calculator works out the weight of grout the joints will hold, how many bags to buy, and how far one bag goes with your settings.
How to use it
- Measure one tile and enter its length and width. For mosaic sheets, use the size of one small tile on the sheet, not the sheet itself.
- Pick the joint width from the spacers you plan to use, and set the joint depth. Tile thickness is a good guide, so 8 mm suits most standard tiles.
- Enter the total area to grout, adding walls and floors together if they use the same grout.
- Choose the grout type and the bag size your shop sells, then read off the weight, the bags and the coverage per bag.
How the calculation works
The calculator uses the standard grout formula. First it finds the length of joint in each square metre from the tile size: (tile length + tile width) divided by (tile length x tile width). That figure is multiplied by the joint width and the joint depth to give the grout volume per square metre, then by the grout density to turn volume into weight. The densities used are 1.6 kg per litre for sanded cement grout, 1.5 for unsanded and 1.7 for epoxy. The total is the rate per square metre times your area, and bags are that total divided by the bag size, rounded up.
Worked example: 30 cm by 30 cm tiles with a 3 mm joint, 8 mm deep, in sanded grout need 0.26 kg per square metre. A 12 square metre floor therefore needs 3.1 kg, so one 5 kg bag covers it, and one bag goes about 19.5 square metres at these settings.
Ready reckoner: common tile sizes at 3 mm joints
Sanded cement grout, 8 mm joint depth. Smaller tiles mean many more joints, which is why the grout per square metre climbs so fast.
| Tile size | Grout per m² | One 5 kg bag covers |
|---|---|---|
| 10 x 10 cm | 0.77 kg | About 6.5 m² |
| 10 x 20 cm | 0.58 kg | About 8.7 m² |
| 15 x 15 cm | 0.51 kg | About 9.8 m² |
| 20 x 20 cm | 0.38 kg | About 13.0 m² |
| 20 x 30 cm | 0.32 kg | About 15.6 m² |
| 30 x 30 cm | 0.26 kg | About 19.5 m² |
| 30 x 60 cm | 0.19 kg | About 26.0 m² |
| 60 x 60 cm | 0.13 kg | About 39.1 m² |
Mistakes to avoid
- Assuming one bag suits every job. A mosaic wall can use six times more grout per square metre than large floor tiles, so always run your own tile size through the calculator.
- Ignoring joint depth. Thick porcelain tiles at 10 to 12 mm deep hold far more grout than thin 6 mm tiles with the same joint width.
- Using sanded grout in very narrow joints or on polished stone. Sanded grout is for wider joints; unsanded suits narrow joints and delicate faces that sand could scratch.
- Mixing a whole bag when you only need part of it. Mixed grout starts to set in the bucket and cannot be stored, so mix smaller batches for small areas.
- Topping up with a different batch later. Grout shades can vary slightly between batches, so buy what you need, plus a spare part bag for repairs, in one go.
Planning the whole tiling job rather than grout alone? The tile calculator works out tiles, boxes, grout and adhesive together, and the backsplash calculator covers the strip above a kitchen counter in detail.
Grout calculator questions
How much grout do I need per square metre?
It depends mostly on tile size. At a 3 mm joint, 8 mm deep, in sanded grout, large 60 cm by 60 cm tiles need about 0.13 kg per square metre, 30 cm tiles about 0.26 kg, and small 10 cm tiles about 0.77 kg. Enter your own tile size above for an exact figure.
What is the difference between sanded, unsanded and epoxy grout?
Sanded grout contains sand for strength and suits joints of about 3 mm and wider. Unsanded grout is smoother, suits narrow joints, and is safer on polished or easily scratched tiles. Epoxy grout is waterproof and stain resistant, popular in showers, but costs more and is harder to work with.
Why does joint depth matter so much?
Grout fills the full depth of the joint, so doubling the depth roughly doubles the grout needed. The default 8 mm matches a standard tile thickness. If your tiles are thicker or thinner, change the depth figure to match and the estimate will follow.
How far does one bag of grout go?
Coverage per bag changes with every setting. One 5 kg bag covers about 19.5 square metres with 30 cm tiles at a 3 mm joint, but only about 6.5 square metres with 10 cm tiles. The calculator shows the coverage per bag for your exact tile and joint settings.
Can I keep leftover grout for repairs?
Dry grout powder keeps well for months if the bag is sealed and stored somewhere dry. Once grout is mixed with water it begins to set and cannot be saved or reused. For small jobs, mix part of the bag at a time so the rest stays usable.
