Tile Calculator




Please check your numbers. Areas and tile sizes need to be above zero, and windows cannot be negative.

Your tile estimate

Tiles to buy

Estimates only. Adhesive assumes one 20 kg bag covers about 4.5 m² (about one 50 lb bag per 50 sq ft). Grout uses an 8 mm joint depth and standard grout density. Always order a little extra from the same batch for future repairs.

Order the right number of tiles, first time. Enter the area, your tile size and the layout pattern, and this tile calculator works out tiles, boxes, grout and adhesive, with waste added for cuts and breakages. Switch to backsplash mode for the strip above a kitchen counter.

How to use it

  1. Measure the length and width of the area. For an L shaped room, tick the second area box and add the extra rectangle.
  2. For a backsplash, choose backsplash mode, enter the total counter run length and the splash height, and add any windows to deduct.
  3. Enter the tile length and width, pick a grout gap, and choose the layout pattern so the right waste allowance is added.
  4. Check the tiles per box figure against the box in the shop, then read off tiles, boxes, grout and adhesive.

How the calculation works

The area is divided by the area of one tile to give the tile count, then the waste percentage for your pattern is added and the result is rounded up. Boxes are that count divided by tiles per box, rounded up again. Grout uses the standard tiling formula, which combines tile size, gap width and an 8 mm joint depth to estimate the weight of grout the joints will hold. Adhesive is estimated at one 20 kg bag per 4.5 m².

Worked example: a 4 m by 3 m bathroom floor is 12 m². With 30 cm by 30 cm tiles, that is 134 tiles before waste, 147 tiles with 10 percent waste added, and 14 boxes at 11 tiles per box. The same job needs about 3.1 kg of grout with a 3 mm gap, so one 5 kg bag, and 3 bags of adhesive.

Waste allowance by pattern

Pattern Waste added Why
Straight lay 10% Few cuts, simple grid
Brick bond 10% Offset rows, end cuts
Diagonal 15% Angled cuts on every edge
Herringbone 20% Many small cuts, tricky ends

Mistakes to avoid

  • Ordering the exact tile count with no waste. Cuts, breakages and one cracked tile later will leave you short, and the next batch may not match.
  • Measuring the room at its widest point only. Out of square rooms need the longest length and width, or tiles run out at the far wall.
  • Forgetting that box counts differ by tile size. Always check tiles per box on the actual box before ordering.
  • Guessing grout. Wide gaps and small tiles use far more grout than wide tiles with tight joints, so run the numbers rather than copying a neighbour’s job.
  • In backsplash mode, forgetting the window above the sink. Deduct it, or you will overbuy.

Working on the strip behind the hob? The dedicated backsplash calculator goes deeper on runs and cutouts. Grout only? Use the grout calculator. Planning the whole room budget, see the bathroom cost calculator and the kitchen cost calculator.

Tile calculator questions

How much waste should I add for tiles?

Add 10 percent for a straight or brick bond layout in a simple room, 15 percent for diagonal layouts, and 20 percent for herringbone. Add a little more for small rooms with many corners, because cuts take a bigger share of each tile.

How is the grout amount worked out?

Grout depends on tile size, gap width and joint depth. Smaller tiles mean more joints and more grout. The calculator uses the standard formula with an 8 mm joint depth, then suggests a sensible bag size so you do not run out mid wall.

Why round up to full boxes?

Tiles are sold in full boxes, and shades vary slightly between production batches. Rounding up to full boxes from one batch keeps the colour consistent and leaves spares for cuts that go wrong and future repairs.

How do I measure a backsplash?

Add up the length of every counter run that needs tiling, then measure from the counter top to the underside of the wall cabinets for the height. Multiply the two for the area, and deduct any window over the sink. Outlets are covered by the waste allowance.

How much adhesive do I need?

As a working rule, one 20 kg bag of adhesive covers about 4 to 5 m² with a standard notched trowel. Large format tiles and uneven floors use more, because the bed is thicker and back buttering is common, so treat the figure as a starting estimate.