Measure first, price second. This worktop calculator (a countertop calculator if you are in the US) works out your total area, linear length and slab or board count from your runs, then gives a supply and fitted cost range for your chosen material.
Estimates only. Rates are broad 2026 fitted ranges per linear measure for standard depth worktops; deep breakfast bar sections cost more per metre and are adjusted in the figures. Real quotes vary by region, stone choice, templating and fitting, so confirm with supplier quotes.
How to use it
- Pick UK or US at the top so sizes and money match how you shop.
- Measure each straight run of worktop in a line and enter up to three runs.
- Choose your depth, upstand height, material and edge profile.
- Read the area and length first for ordering, then the supply and fitted ranges for budgeting.
How the calculation works
Total area is the combined length of your runs multiplied by the depth, plus the upstand strip (total length multiplied by upstand height). Slab counts for granite, quartz and marble assume a typical slab of 320 cm by 190 cm with about 4.5 m² (48 sq ft) of usable material once edging, cutouts and awkward grain matching are allowed for. Laminate and wood are counted in standard 3 m (10 ft) lengths instead. Hob and sink cutouts do not reduce the area you order. Suppliers cut them from full slabs or boards, and the removed pieces are waste, which is why the area stays whole; the cutouts matter for the fitting charge, not the material quantity. Cost is the linear length multiplied by a per metre or per foot rate for your material, with an uplift for deep sections and decorative edges.
Worked example: runs of 300 cm and 200 cm at 60 cm depth give 5 m of worktop and 3.0 m² of surface. A 10 cm upstand adds 0.5 m², so 3.5 m² in total, which is one slab of quartz. Fitted at £420 to £700 per metre with a bevel edge, the budget lands at £2,210 to £3,680.
Standard sizes worth knowing
| Item | UK size | US size |
|---|---|---|
| Standard worktop depth | 60 cm | 25.5 in |
| Breakfast bar depth | 90 cm | 36 in |
| Laminate board length | 3 m or 4.1 m | 10 ft |
| Typical stone slab | 320 x 190 cm | 126 x 75 in |
| Usable slab area | About 4.5 m² | About 48 sq ft |
Mistakes to avoid
- Double counting a corner where two runs meet. Measure each wall once in a straight line.
- Subtracting the hob and sink from your order area. You still pay for the full slab or board.
- Forgetting the upstand. It adds real area and cost on long runs.
- Ordering stone by area alone. Grain direction and joins can push a job into a second slab.
- Measuring before the cabinets are fitted and level. Final stone templating happens after installation.
Keep planning your kitchen
Put the worktop figure into the full budget with our kitchen cost calculator, plan the tiled area behind it with the backsplash calculator, and work out floor or wall tiles with the tile calculator.
Questions people ask
How do I measure my kitchen worktop?
Measure each straight run from wall to the end of the run in one line, then add the runs together. Note the depth from the wall to the front edge, and measure upstands separately by their height along the same length.
Do hob and sink cutouts reduce how much worktop I buy?
No. The cutouts are cut from full boards or slabs and the offcuts cannot be reused, so suppliers charge for the whole area. Cutouts do add to the fitting cost, which is why they are counted in this tool as a note.
How many slabs of quartz or granite do I need?
Divide your total area by about 4.5 m² (48 sq ft) of usable slab and round up. Kitchens with long runs, islands or strong veining often need an extra slab so the grain matches across joins.
What is the standard worktop depth?
Standard depth is 60 cm in the UK and 25.5 inches in the US, which covers standard cabinets with a small front overhang. Breakfast bars and islands are usually 90 cm or 36 inches deep.
Why is fitted cost so much higher than supply only?
Stone worktops are templated on site, cut and polished in a workshop, delivered by a two person team and sealed in place. That labour and handling is a large share of the price, unlike laminate which a joiner can cut and fit the same day.
